No Hot Water in Kildare
No hot water in Kildare? Loss of hot water is usually caused by a boiler fault, failed immersion heater, or problem with the hot water cylinder. The plumbers and gas installers listed below serve Co. Kildare and can diagnose and fix the cause. For a gas boiler fault, check that the boiler display shows no error code before calling, and ensure the gas supply is on.
Plumbers in Kildare for no hot water
Pat Tobin Construction LTD
Kildare
Adrian E Lee
Robertstown
087 8097300
Brendan Keane
Donadea
0879938684
Danny Trundle Heating & Plumbing
Co. Kildare
086 2572720
Nay-Cab Irl Ltd T/A Clane Fireplaces
Clane
085 7855329
RMI Services
Naas
086 8260657
Norman Birchall Heating & Plumbing
Maynooth
087 2786925
Bam FM Ireland Ltd
Kildare
087 2892039
Martin Cunningham
Clane
083 4447036
True-Temp Heating Solutions LTD
Naas
0851215403
SMD Gas and Oil Services
Maynooth
087 6147355
Florin Heating and plumbing LTD
Maynooth
086 3455108
Elton Heating & Plumbing
Leixlip
086 2513413
Whelans Property Maintenance LTD
Athy
086 3736680
TM Plumbing & Heating Ltd
Newbridge
087 6793864
R.P Heating & Plumbing
Newbridge
085 7732741
Martin Buggy Plumbing t/a Gas Safety Services - R
Sallins
086 1708598
Kmech Mechanical Ltd
Naas
0831733235
CK Plumbing & Heating
Clane
087 2213602
Christopher Turley
Rathangan
086 3382800
Showing 20 of 138 plumbers in Kildare. See all 138 listings.
What to do when you have no hot water in Kildare
No hot water in a Kildare home is most commonly caused by a boiler fault, a failed immersion heater element, a faulty thermostat on the hot water cylinder, an airlock in the system, or loss of gas or oil supply. Before calling a plumber, check that the boiler is on and showing no fault code, that the gas meter is active, that the immersion heater switch is on if you have a cylinder system, and that the programmer is set correctly for hot water. If none of these identify the problem, you need a plumber or RGI registered gas engineer.
Gas combi boilers in Kildare homes produce hot water on demand directly from the boiler without a separate cylinder. If a combi boiler fails, all hot water is lost immediately and there is no backup. Properties with a separate hot water cylinder have a backup in the immersion heater, which can provide hot water even when the boiler is not working. RGI registered gas installers must carry out any repair involving the gas components of a boiler, including the gas valve, heat exchanger and burner. Electrical and controls faults may be repaired by a qualified plumber or electrician without RGI registration.
How much does no hot water repair cost in Kildare?
| Job type | Typical cost in Kildare |
|---|---|
| Boiler fault diagnosis | €80 to €150 |
| Diverter valve replacement | €200 to €400 |
| Boiler PCB replacement | €250 to €600 |
| Gas valve replacement | €200 to €500 |
| Immersion heater element replacement | €120 to €250 |
| Hot water cylinder thermostat replacement | €80 to €160 |
Diagnosing no hot water in a Kildare home typically costs €80 to €150 as a call-out and inspection fee. The repair cost depends entirely on the cause. Common fault parts such as the diverter valve on a combi boiler typically cost €100 to €250 for the part plus one to two hours of labour. More complex faults such as a failed PCB or gas valve are more expensive but are still far less than a full boiler replacement.
Immersion heater repairs in Kildare are among the more straightforward no-hot-water fixes. A failed element typically costs €60 to €100 for the part, with call-out and labour bringing the total to €120 to €250. If the immersion heater has not been replaced in over ten years, full replacement of the immersion unit rather than just the element is often recommended, as the thermostat and element tend to reach the end of their service life at similar ages.
How a no hot water call-out works in Kildare: step by step
Initial fault diagnosis
The engineer begins by questioning you about what symptoms you have observed — whether there is no hot water only, or no hot water and no heating, whether the boiler fired recently, and whether any error code is displayed. This narrows the likely cause before any component is inspected. For combi boilers, the error code displayed is the single most important diagnostic piece of information for a Kildare gas engineer arriving on site.
System checks and error code reading
The engineer checks gas supply pressure at the meter, boiler water pressure, the programmer settings and any displayed fault codes. For cylinder systems, the immersion thermostat and element are tested with a meter. The engineer checks whether the boiler fires and at what point in the sequence it fails or locks out. Each fault code points to a specific component — most boiler brands provide clear fault code tables in the technical manual.
Component replacement or repair
Once the fault is identified, the failed component is replaced. For a combi boiler diverter valve fault in a Kildare home, this involves draining the relevant section of the boiler, removing the valve, fitting the replacement and refilling. For an immersion element, the element is unscrewed from the cylinder and replaced with a correctly rated new unit. Gas components are only replaced by the RGI registered engineer attending.
System test and hot water confirmation
After the repair, the hot water system is run fully — the boiler is fired, hot water is drawn at a tap and the temperature is checked. For cylinder systems, the immersion is run and the thermostat cutout temperature is verified. The engineer confirms that the fault code has cleared and that the system is running correctly before completing the job. Written documentation of the fault found and parts replaced is provided on departure.
Legal requirements for no hot water repairs in Kildare
No hot water faults involving the gas components of a boiler in Kildare must be diagnosed and repaired by an RGI registered gas installer. This includes the gas valve, burner, heat exchanger, flue and gas supply connection. A plumber who is not RGI registered may diagnose the boiler controls and electrical components but cannot open the gas circuit. Always confirm whether your Kildare call-out engineer is RGI registered if the fault is likely gas-related.
Immersion heater repairs and replacements in Kildare are not gas work and can be carried out by any qualified plumber. However, the electrical connection of an immersion heater — particularly new cabling between the immersion switch and the element — is notifiable electrical work under Safe Electric regulations. If your plumber identifies that the immersion wiring needs replacement, a RECI or Safe Electric registered electrician should complete that element of the work separately.
How to choose an engineer for no hot water in Kildare
Confirm RGI registration for gas boiler faults
If your Kildare home has a gas boiler and the fault is likely gas-related — no firing, gas pressure fault, gas valve error code — confirm the engineer is RGI registered before booking. Call two or three RGI engineers simultaneously and book the first one available rather than waiting for a specific engineer. In winter, gas engineers in Kildare are often fully booked for emergency call-outs by mid-morning.
Provide boiler make, model and error code when calling
When calling a Kildare gas engineer about a no hot water fault, have the boiler make, model and any displayed error code ready before you dial. This allows the engineer to bring the correct replacement parts on the van, which may mean the fault can be fixed on the first visit rather than requiring a return call. The boiler model is typically on a label inside the front panel.
Ask about availability of common parts
Some boiler faults require specific parts that not all Kildare engineers stock. For older boilers, parts may need to be ordered from a supplier, which adds one to two days to the repair time. Ask the engineer whether the likely fault part is available on the van or if a parts run will be required. This is especially relevant in winter when demand for boiler parts is high across Co. Kildare and lead times are longer.
Consider boiler age in the repair versus replace decision
For a boiler in Kildare that is over twelve years old, the cost of a major component repair should be weighed against the cost of a full boiler replacement. An engineer who quotes €400 to replace a PCB on a thirteen-year-old boiler should also provide a boiler replacement quote so you can make an informed decision. Repairing an old boiler can make sense for minor faults but becomes poor value for major components on ageing units.
No hot water in Kildare: frequently asked questions
Why is there no hot water but the heating is working in my Kildare home?
On a combi boiler, this usually indicates a failed diverter valve. The diverter valve switches heat between the central heating circuit and the domestic hot water heat exchanger. When it fails in the heating position, radiators work but there is no hot water. A Kildare gas engineer can replace the diverter valve, typically costing €200 to €400 all-in for parts and labour.
Why is there no hot water and no heating in my Kildare home?
Both systems failing simultaneously points to the boiler itself — a lockout fault, gas supply issue, failed PCB or pump failure. Check the boiler display for an error code and look it up in the boiler manual before calling. Check that your gas supply is working by testing another appliance such as the hob. If the boiler shows no fault code but will not fire, call an RGI registered gas installer in Kildare.
How do I reset a boiler that has lost hot water in Kildare?
Most boilers have a reset button on the front panel or in the menu. Press and hold for five seconds. If the boiler fires and runs for a few minutes then locks out again, there is an underlying fault that needs diagnosis. Do not repeatedly reset a boiler that keeps locking out — a safety trip is activating for a reason. Call a Kildare gas engineer if it locks out more than twice in succession.
My hot water is lukewarm but not fully hot in Kildare — what causes this?
Lukewarm water on a combi boiler usually indicates a failing heat exchanger or limescale buildup inside it. On a cylinder system, a failed or incorrectly set thermostat is the most common cause. Hard water areas in parts of Co. Kildare accelerate limescale accumulation inside heat exchangers and cylinders. A gas engineer can descale or replace the heat exchanger and a plumber can check and replace a cylinder thermostat.
How long can I manage without hot water in Kildare before getting it repaired?
A boiler failure in winter in Kildare should be treated as an urgent matter — you lose both hot water and heating simultaneously on a combi boiler system. Most gas engineers in Kildare prioritise emergency boiler calls in winter. If your cylinder has an immersion heater, switch it on immediately as a backup while waiting for the boiler repair. Summer failures are less urgent but should still be addressed within a few days.
Is no hot water covered by my home insurance in Kildare?
Standard home insurance does not cover boiler breakdowns in Co. Kildare. Boiler cover or home emergency cover is an optional add-on offered by most Irish insurers and energy suppliers including Bord Gáis Energy. If you have such a policy, call the emergency number on the policy document — they will dispatch an RGI registered engineer in Kildare at no additional cost for covered faults.
Find a plumber in Kildare
Browse the full directory of local plumbers in Co. Kildare and contact them directly.