Leaking Tap Repair in Roscommon
Looking for a plumber to fix a leaking tap in Roscommon? A dripping tap wastes thousands of litres of water per year and can cause limescale and staining. Most repairs take under an hour. The directory below lists local plumbers in Co. Roscommon who can diagnose and fix leaking taps, replace washers and repair mixer taps.
Plumbers in Roscommon for leaking tap repair
Stephen McGuinness Plumbing Ltd
Tarmon Barry
086 6016548
Frank Cuffe Cooker Repairs
Castlerea
087 2357289
T/A O'Boyle Services
Carrick-on-shannon
087 0621180
Best West Heating & Plumbing
Athleague
087 1494865
Joseph Kenny Heating & Plumbing Ltd
Castlerea
087 2508570
McCormack Plumbing & Construction Ltd.
Co. Roscommon
086 8115339
Michael Connor Construction
Castlerea
086 3823712
David Hughes
Fourmilehouse
097 0952392
Roscommon Heating & Plumbing Ltd
Roscommon Town
086 8125137
MGW Energy Services Ltd
Roscommon
086 0283733
Update Heating Ltd
Castlecoote
087 2587537
What leaking tap repair in Roscommon involves
Leaking tap repair in Roscommon covers diagnosing the source of the drip, replacing worn washers, O-rings or cartridges, and reassembling the tap correctly. Traditional pillar taps use rubber washers that compress against a seat to stop water flow — these wear out over time and drip when the tap is turned off. Modern mixer taps use ceramic disc cartridges, which are more durable but fail suddenly rather than wearing gradually. A plumber can typically repair or replace the internal mechanism of most tap types within 30 to 60 minutes.
A dripping tap in a Roscommon home wastes more than 5,500 litres of water per year if it drips once per second, adding to water usage and, in properties on private wells in rural Co. Roscommon, draining the pump system unnecessarily. Limescale is the most common cause of tap failure in hard water areas and builds up around the cartridge or washer seat, preventing a full seal. If a tap has been dripping for an extended period, the seat itself may be pitted and need re-grinding, or the entire tap may need replacing rather than a simple washer change.
How much does leaking tap repair cost in Roscommon?
| Job type | Typical cost in Roscommon |
|---|---|
| Tap washer replacement | €60 to €120 |
| Ceramic cartridge replacement | €80 to €160 |
| Mixer tap replacement (labour only) | €100 to €200 |
| Full tap replacement (supply and fit) | €150 to €400 |
| Isolation valve fitting | €80 to €150 |
| Tap seat re-grinding | €100 to €180 |
Leaking tap repair costs in Roscommon are among the lowest call-out jobs in plumbing. A simple washer replacement takes under an hour and typically costs €60 to €120 all-in. If the tap is a mixer with a ceramic cartridge, the replacement costs more due to part cost but the labour is similar. Always ask your Roscommon plumber whether a repair or full replacement is more cost-effective given the age and condition of the tap before committing.
Replacing a tap entirely often costs little more than repairing an old one once parts and labour are included, particularly for budget-range taps. If your Roscommon home has taps that are more than fifteen years old, leaking, discoloured or difficult to operate, full replacement is usually the better investment. Your plumber can supply a replacement in a similar style and finish, or you can source your own from a Roscommon bathroom showroom or builders merchant.
How leaking tap repair works in Roscommon: step by step
Diagnosis and water isolation
The plumber identifies the source of the leak — whether it is dripping from the spout (washer or cartridge fault), leaking around the base (O-ring failure) or weeping from the connection below the sink (supply pipe joint). The water supply to the tap is isolated using the service valve on the supply pipe or the main stopcock if no service valve is present. For taps with no accessible isolation valve, the engineer will fit one as part of the repair.
Disassembly and part inspection
The tap head is removed and the internal mechanism inspected. For pillar taps, the spindle, gland packing and washer are examined for wear. For mixer taps, the cartridge is removed and checked for cracking, lime deposits or mechanical failure. The seating surface inside the tap body is checked for pitting or scoring that would prevent a new washer from sealing correctly even after replacement.
Washer or cartridge replacement
The worn washer, O-ring or cartridge is replaced with a new part. For standard pillar taps in older Roscommon homes, a rubber washer and fibre washer are typically available from a plumber's van stock. For ceramic cartridge mixer taps, the cartridge is brand-specific — a quality plumber will identify the brand and fit the correct replacement. A generic cartridge that does not match the original may seal initially but fail prematurely.
Reassembly and pressure test
The tap is reassembled, the water supply is restored and the tap is tested through several full open-close cycles to confirm the repair is holding under pressure. The plumber checks for any residual weep around the gland or spout connection under running water. A properly repaired tap in a Roscommon home should close completely with normal hand pressure and show no drip within 30 seconds of closing.
Regulations for tap repair and replacement in Roscommon
Tap repair and replacement in Roscommon is not notifiable work under Building Regulations or the Gas (Interim) (Regulation) Act 2002, as it involves cold and hot water supply pipework only. Any competent plumber can carry out this work. The only regulatory consideration is that the water supply to the tap must be isolated correctly before any disassembly — using the service valve on the supply pipe or the main stopcock if no service valve is accessible.
Properties in Roscommon on private group water schemes or wells should note that any changes to internal plumbing that significantly increase water demand should be notified to the scheme operator. For standard tap repair or replacement, this is not a practical concern. Addition of a new outdoor tap or garden irrigation connection on a mains-connected Roscommon property may require notification to Uisce Éireann depending on the local scheme agreement.
How to choose a plumber for leaking tap repair in Roscommon
Confirm they stock common tap parts
A good Roscommon plumber carries common washer sizes, O-rings and cartridges for the most frequent tap brands on their van. This allows tap repairs to be completed in a single visit without a return call for parts. Ask before booking whether the engineer is likely to have the correct parts on the van — for very old or unusual taps, the cartridge may need to be ordered and the job completed on a second visit.
Ask about the full scope of the call-out
A plumber visiting your Roscommon property for a leaking tap can often address other minor plumbing issues on the same call-out for a small additional charge, such as a slow drain, dripping showerhead or an isolation valve that needs replacing. Having a list of minor issues ready when the plumber arrives makes the most of the call-out charge and avoids booking a second appointment for related work.
Get a fixed price for the repair
Leaking tap repair is straightforward enough that most Roscommon plumbers can quote a fixed price for the call-out and repair, with any additional cost for parts above the standard washer or cartridge noted separately. A fixed price protects you from call-out rates that escalate if the engineer discovers the issue is more complex than a standard washer change.
Check whether a new tap is better value
Ask your Roscommon plumber for an honest assessment of whether the tap is worth repairing or whether replacement is the better value option. A tap that has been dripping for years on a hard water supply in Co. Roscommon may have a damaged seat that makes the repair only a temporary fix. An honest plumber will tell you if the tap is beyond economic repair and provide a price for supply and fit of a new unit.
Leaking tap repair in Roscommon: frequently asked questions
Can I replace a tap washer myself in Roscommon?
Yes, if you are reasonably confident with basic DIY. Turn off the water supply at the service valve under the sink or at the main stopcock, drain the supply pipe, remove the tap head, replace the washer or cartridge, and reassemble. The most common mistake is not fully draining the supply before opening the tap body. If you are uncertain, a Roscommon plumber can do the job in under an hour for a modest call-out charge.
Why is my tap dripping even after I tighten it?
Tightening a tap that is dripping due to a worn washer only presses the damaged washer harder against the seat — it does not fix the underlying problem. If tightening the handle has no effect, the washer or cartridge needs replacement. Overtightening also damages the seat, making the repair more complex and expensive. A Roscommon plumber will disassemble the tap and replace the worn internal component rather than tightening it.
How much water does a dripping tap waste in a Roscommon home?
A tap dripping at one drip per second wastes approximately 10 litres per hour, or around 5,500 litres per year. For a hot tap, this also represents wasted heating energy. For properties in rural Co. Roscommon on private wells, dripping taps cycle the pump unnecessarily, increasing electricity costs and reducing pump life. The repair cost is almost always recovered in energy and water savings within a few months.
My tap has no service valve under the sink — what do I do in Roscommon?
Without a service valve, you must turn off the main stopcock to work on the tap. The stopcock is usually under the kitchen sink or where the water main enters the Roscommon property. If no stopcock is accessible or it is seized, a plumber can turn the supply off at the water meter before disassembly and also fit a new service valve during the repair, preventing the same problem in future.
What is the difference between a washer tap and a cartridge tap?
Pillar taps and older traditional mixer taps use rubber washers that compress against a brass seat to create a water seal. These wear gradually and usually begin dripping slowly before failing completely. Modern single-lever and quarter-turn mixer taps use ceramic disc cartridges that are more precise and durable but tend to fail suddenly. Cartridge replacement costs more than a washer change but the process is the same — disassemble, replace, reassemble.
Should I repair or replace a leaking tap in my Roscommon home?
If the tap is less than fifteen years old and in otherwise good condition, repair is usually cost-effective. If the tap is old, corroded, difficult to operate or visually dated, full replacement costs only marginally more once a Roscommon plumber is already on site. Ask for an honest assessment of whether the internal components are repairable or whether replacement offers better long-term value.
Find a plumber in Roscommon
Browse the full directory of local plumbers in Co. Roscommon and contact them directly.